Custom press-fit feedneck boss adapters Item detals: Nummech offers a custom installation service to retrofit modern latching feednecks onto markers that previously used press-fit high-rise non-clamping feednecks. The new adapter allows the use of any modern latching feedneck built to Empire's mount dimensions, from Nummech or otherwise.

The press-fit adapter must be precisely installed, so we highly recommend sending your marker body in for proper installation. Press-fit adapters are meant to be a permanent modification, therefore they must be installed with care. We will also remove the existing feedneck without damage to the marker body, and the old feedneck will be returned to you.

    Features:
  • Inside surface is engraved with the associated body for identification.
  • Machined from solid billet aluminum 6061-T6 and plated with type-2 anodizing.
  • Lifetime limited warranty included. If the adapter becomes damaged in the future, we can easily install a new one for you (shipping fees will apply)

We've built many styles of press-fit adapters available for the markers listed below. If a custom adapter is needed for your particular marker body, it can be manufactured at no additional cost (however it will take some extra time for anodizing).

"WGP 970" height: compatible with press-fit WGP vertical feed Autococker bodies that use a siterail, which includes MANY different bodies that were milled from WGP blanks (STO, Prostock, Reflex, 32 degrees, Lotus, SFL, Outkast with siterail, others). The adapter has a cutout for left-side ball detent.
WGP 2000 press-fit feedneck adapter WGP 2000 press-fit feedneck adapter WGP 2000 press-fit feedneck adapter WGP Outkast press-fit feedneck adapter WGP STO press-fit feedneck adapter

"WGP 970" height with no detent hole: compatible with press-fit WGP Autococker bodies with a siterail, but the marker body must utilize a wire detent.
WGP 2000 press-fit feedneck adapter WGP 2000 press-fit feedneck adapter

"WGP 1150" height: identical to WGP vertical feed bodies with a siterail, but this adapter allows use of an Eclipse feedneck rather than our normal Empire adapters.
WGP Eclipse press-fit feedneck adapter WGP Eclipse press-fit feedneck adapter

"WGP 880" height: compatible with some press-fit WGP Autococker bodies that have no siterails. The example marker was a WGP Outkast with no siterail (but other Outkast bodies may require a different adapter due to different milling).
WGP Outkast press-fit feedneck adapter

"WGP 810" height: compatible with WGP Superstock 2005 bodies.
WGP 810 press-fit feedneck adapter

"WGP 830" height: compatible with WGP Orracle and Karnivore bodies.
WGP 830 press-fit feedneck adapter WGP Orracle press-fit feedneck adapter WGP Karnivore press-fit feedneck adapter

"WGP 785" height: compatible with WGP Black Magic Autococker bodies.
WGP Black Magic press-fit feedneck adapter

"WGP 940" height: compatible with ANS GX4 Chaos Autococker bodies.
GX4 Chaos press-fit feedneck adapter

"WGP 995" height: compatible with System-X Vengeance Autococker bodies. The adapter is slightly taller and wider than the WGP versions (diameter is +0.005 compared to WGP bodies).
Vengeance press-fit feedneck adapter

"DYE 984" height: compatible with Dye Reflex bodies that were intended to use set screws. These feedneck adapters are enlarged to be pressed into the body; they don't use the factory set screw system.
Dye Reflex set screw press-fit feedneck adapter

"SP 580" height: compatible with press-fit Smart Parts 2000 Impulse or 2000 vertical feed Shocker Sport.
Shocker Sport 2000 press-fit feedneck adapter Shocker Sport 2000 press-fit feedneck adapter

"SP 580" height adapter is also compatible with press-fit Bob Long Dragon and Species Intimidator. Other Intimidators have yet to be tested but we can make an adapter for any Intimidator body.
Dragon Intimidator press-fit feedneck adapter

"BL 450" height: compatible with press-fit Bob Long Dark Intimidator bodies.
Dark Intimidator press-fit feedneck adapter

"BL 505" height: compatible with press-fit Bob Long Alias Intimidator bodies.
Alias Intimidator press-fit feedneck adapter

"BL 525" height: compatible with press-fit Bob Long Ironmen and Ground Zero Intimidator bodies.
Ironmen Intimidator press-fit feedneck adapter Ground Zero Intimidator press-fit feedneck adapter

"IMP 808" and "IMP 630" heights: compatible with Smart Parts 09 Impulse marker. The adapters use a stepped diameter, and effectively eliminate the Impulse feedneck wobble problem. Two different adapters are available, depending on your feedneck choice:
IMP 808 adapter is compatible with the stock/OEM '09 Impulse feedneck. This adapter is not compatible with Empire's feedneck, unlike all other adapters listed on this page.
09 Impulse press-fit feedneck adapter 09 Impulse press-fit feedneck adapter
IMP 630 adapter is compatible with Empire's feedneck system, allowing you to use an Empire-spec feedneck in situations where the original Impulse feedneck is not available, or if you wish to use our No-Rise feedneck which offers a different height compared to the stock feednecks.
09 Impulse press-fit feedneck adapter 09 Impulse press-fit feedneck adapter 09 Impulse press-fit feedneck adapter

"AGD 740" height: compatible with AGD X-Mag breeches.
X-mag press-fit feedneck adapter X-mag press-fit feedneck adapter

"RM 855" height: compatible with Brass Eagle Rainmaker bodies.
Rainmaker press-fit feedneck adapter

Press-fit feedneck cost: Sorry, unfortunately we aren't accepting markers for the retrofit due to high workload. We will update this page if we're able to provide the service in the future.

For record purposes: this mod costs $14.99 plus shipping.

Content corner